Skip to content
Quanscient logo Quanscient Allsolve Docs

Overview

Tutorials are hands-on simulation walkthroughs, grouped by application area. Within each area, the numbered series builds up from the basics — start at 001 and work forward, or jump straight to the case that matches your problem.

Solid mechanics

Section titled “Solid mechanics”
Bending of a cantilever beam
Simulate the bending of a cantilever beam subjected to a uniform bending load.

Magnetism

Section titled “Magnetism”
Permanent Magnets
Setup permanent magnets simulation.

Electric motors

Section titled “Electric motors”
PMSM 2D torque analysis - EM 001
2D permanent magnet synchronous motor with torque sweep and reference comparison
IM 2D torque analysis - EM 002
2D induction motor transient simulation validated against TEAM Problem 30
Permanent magnet synchronous electric motor
Demonstration of simulating torque on a permanent magnet synchronous motor with magnetostatic approach using the phi-formulation.

Superconductors

Section titled “Superconductors”
HTS tape AC loss - SC 001
Simulating AC loss in a high-temperature superconducting tape
Twisted superconductor AC Loss - SC 002
Simulating AC loss in a twisted filament superconducting wire
Quench - SC 003
Multiphysics quench simulation in a YBCO tape with temperature-dependent critical current

MEMS

Section titled “MEMS”
Combdrive eigenmodes - MEMS 001
Eigenmode analysis of a MEMS combdrive accelerometer from a GDS layout
Combdrive static deflection - MEMS 002
Electrostatic actuation and voltage sweep on a MEMS combdrive
Viscoelasticity benchmark - MEMS 003
Transient viscoelastic rod benchmark with Prony series and analytical comparison
Simulate pull-in of an electrostatic MEMS actuator
Build a multiphysics model, sweep voltage, and compare the pull-in point to a closed-form estimate.

Ultrasound

Section titled “Ultrasound”
PMUT Unit cell - Ultrasound 001
Build and simulate a piezoelectric PMUT unit cell with acoustic–elastic coupling, from variables and geometry through mesh extrusion and transient results.
PMUT 11x11 array - Ultrasound 002
11x11 PMUT array with transient piezoelectric excitation, mesh extrusion, and Kirchhoff-Helmholtz beam pattern extraction
Piezocomposite transducer
1-3 piezocomposite transducer element with transient wavelet excitation

Acoustics

Section titled “Acoustics”
Loudspeaker in a cabinet
Multiphysics loudspeaker model with acoustic waves, solid mechanics, and a PML boundary
SAW unit cell
Piezoelectric surface acoustic wave unit cell with anisotropic materials and periodic boundaries

Radio frequency

Section titled “Radio frequency”
Eigenmode ports and S-parameters - RF 001
Microstrip line with eigenmode port excitation and S-parameter extraction
Lumped ports and RLC components - RF 002
Grounded coplanar waveguide with a lumped resistor port and impedance sweep
Patch antenna - RF 003
Patch antenna with airbox PML, S-parameters, and radiation pattern extraction

Heat transfer

Section titled “Heat transfer”
Manifold microchannel heat sink - CHT 001
Conjugate heat transfer in a microchannel heat sink with temperature-dependent viscosity
2D Taylor-Couette flow - CHT 002
Conjugate heat transfer between rotating concentric cylinders with analytical verification
Static heat transfer in solid materials - NAFEMS Benchmark
Simulate the heat transfer in a solid block subjected to constant temperature boundary conditions

Packaging

Section titled “Packaging”
FCBGA free warpage - Packaging 001
Free warpage and thermal stress in an FCBGA package with temperature-dependent materials

Harmonic balance

Section titled “Harmonic balance”
AC Joule heating - HB 001
Multiharmonic Joule heating in an aluminium wire with frequency sweep
Backbone curve of a clamped-clamped beam - HB 002
Nonlinear resonance backbone curve using multiharmonic continuation
MEMS Microspeaker - HB 003
Multiphysics microspeaker with electrostatics, fluid, and harmonic distortion analysis